How do you program a HM10 module?

How do you program a HM10 module?

Just connect as following:

1. Connect 3.3V of Arduino to the VCC of HM-10.
2. Connect GND of Arduino to the GND of HM-10.
3. Connect D8 of Arduino to RX of HM-10.
4. Connect D7 of Arduino to TX of HM-10.
5. Connect D2 of Arduino to the long leg of LED along with a 220 ohm resistor.
6. Connect the short leg of LED with the GND of Arduino.

What is HM10 Bluetooth module?

HM-10 BLE Bluetooth 4.0 CC2541 Wireless Module is a BLE module for an embedded system to get BLE wireless communication with BLE capable devices (e.g. Android, iPhone, and iPad).

How do I pair my HM10 Bluetooth module?

BLE Scanner Android App

1. Once the installation is completed, open the App and enable Location and Bluetooth permission.
2. Scan for the bluetooth devices. The name of HM-10 BLE 4.0 is MLT-BT05. The default pairing code for MLT-BT05 is 123456789. So once connected, you are ready to go now.

What is difference between HC 05 and HM10?

Difference between HM10 and other Bluetooth Module The major difference HM10 possess is the Bluetooth Version. The HM10 is Bluetooth 4.0 module, so it comes with all Bluetooth Version 4.0 features such as speed, throughput and range. The HM10 offers a data rate of up to 24 Mbps with low-energy/low-power consumption.

How do I connect my Arduino Uno to my phone?

You Will Need

1. Android Phone – The phone used needs to support USB Host Mode (i.e OTG Support).
2. Arduino – Any version will do, but we used an Uno R3.
3. Arduino USB Cable.
4. USB OTG Cable – This component connects the USB cable of your Arduino to the micro-USB port of your Android phone.

How do I change the baud rate of HM-10?

1. There are 2 versions of the HM-10; the HM-10C and the HM-10S.
2. Tapping one of the labels will read the characteristic value. For example, under Device Name, tapping the.
3. At the bottom of the serial monitor, set the baud rate to 9600 and using the above sketch means we can have line end characters selected:

What is the max range of Bluetooth?

approximately 30 feet
The range of the Bluetooth® connection is approximately 30 feet (10 meters). However, maximum communication range will vary depending on obstacles (person, metal, wall, etc.) or electromagnetic environment.

Can you connect Arduino to phone?

Android Phone which supports USB Host Mode (i.e., OTG Support) – Most devices running Android 3.1+ support this. Check if your phone does using the USB Host Diagnostics App from the Play Store. USB OTG Cable – You will need this to connect the USB cable of the Arduino to the micro-USB port of the Smartphone.

How to connect HM-10 module to discovery board?

Connect USART2 and power to HM-10 on the Discovery board using following pins: Attach any preferable UART-to-USB converter such as this module according to following pinout: To be able to communicate with HM-10 module via Android smartphone, a special application must be installed.

Who is the manufacturer of the HM 10 Bluetooth module?

The HM-10 is made by Jinan Huamao and is one of many Bluetooth devices they produce including the HM-11 which is operationally the same as the HM-10 but has a smaller footprint with fewer pins broken out. There are 2 versions of the HM-10; the HM-10C and the HM-10S

Are there any programmable pins on the HM-10?

HM-10 Programmable Pins. The HM-10 has 10 pins that can be user controlled, a couple are input only, the others can be input or output. Unfortunately, the pins we can control are not available on the breakout board so we need to attach a connection directly to the actual HM-10 (the small daughter board).

How does the HM-10 talk to other BLE devices?

There are 2 ways BLE devices can talk to each other; Broadcaster + Observer, and, Central + Peripheral. The HM-10 can use both methods. With Broadcaster + Observer there isn’t a standard connection, the Broadcaster, usually some kind of sensor, sends out periodic signals (advertising packets) which the Observer listens for.