How do I manage my HP ProCurve switches?

How do I manage my HP ProCurve switches?

How to: Configure a HP ProCurve switch

1. Step 1: Connect your serial connection.
2. Step 2: Conenct PuTTY.
3. Step 3: Get the IP address.
4. Step 4: Set time server.
5. Step 5: Set SNMP community info.
6. Step 6: Launch the web GUI.
7. Step 7: Configure basic info.
8. Step 8: Create VLANs.

How do I show config on HP switch?

To display the running configuration using the WebAgent:

1. In the navigation pane, click Troubleshooting.
2. Click Configuration Report.
3. Use the right-side scroll bar to scroll through the configuration listing.

How do I ping an HP switch?

Information. The ping command by default will use the IP address of the VLAN configured for the outgoing interface as the “source address” for the IP packet. Using the command qualifier “Source” with the ping command allows for different source IP addresses.

How do I connect my HP switch to the console?

To connect a console to the switch, use the console cable shipped with the switch and connect a PC or VT-100 terminal to the console serial port. The PC or terminal then functions as a management console connected directly to the switch.

How do I log into my HP switch?

To enable web login, log in to the device via the console port, and perform the following configuration: • Enable HTTP or HTTPS service • Configure the IP address of the VLAN interface • Configure a username and password The device supports the following web login methods: • HTTP login: • HTTPS login: The following …

How do I check core switch settings?

Initial command prompt “Switch>” appears on the screen. Type “enable” next to it and press “Enter”. This will take you into the “EXEC” mode, also known as the Global Configuration mode.

How do I find the running-config of an interface?

To display the running configuration for a specific port channel, use the show running-config interface command.

How do I console my extreme switch?

Console port access via CLI

1. Connect to the switch’s Console port using your serial cable/adapter and a terminal emulator program such as PuTTY, TerraTerm or HyperTerminal.
2. Serial port settings are 9600 baud rate, 8, n, 1.
3. Log into the switch using the default user. you may need to hit enter to get the login prompt:

How do I connect my HP 2530 to a console?

To connect a console to the switch, follow these steps: Connect the PC or terminal to the switch’s Console Port using the console cable included with the switch. (If user’s PC or terminal has a 25-pin serial connector, first attach a 9-pin to 25-pin straight-through adapter at one end of the console cable.)

How do I find the IP address of my HP switch?

A switch should have a web interface and a telnet interface. Another approach would be to use the arp command to find its IP address from the Mac address (which should be physically labeled on it somewhere).

How do I enable GUI on HP switch?

How to connect to a HP ProCurve switch?

Get answers from your peers along with millions of IT pros who visit Spiceworks. I am trying to connect to a HP ProCurve switch for the first time using Putty.exe and a Trendnet serial to USB adapter. However upon opening the connection all I get is a black screen which will not take any input from the keyboard.

How to do the HP ProCurve CLI cheat sheet?

– #link-test — Test connectivity between switches (local switch and destination switch) – #ping — Ping IP 192.168.0.1 – #chassislocate — Turn on/off switch locator led or blink it (30 minutes) – #chassislocate blink — Blink switch locator led set time in minutes – #ntp1 — Add time server to NTP server list

Where do I enter the manager password in hp switch?

The prompt for the Manager level contains only the system name and the “#” delimiter, as shown above. To select this level, enter the enablecommand at the Operator prompt and enter the Manager password, when prompted. For example: HP Switch> enable Password: HP Switch# _ Enter enable at the Operator prompt.

How to see the privilege level of a hp switch?

HP Switch(config)# vlan 10 HP Switch(vlan-10)# Privilege level hierarchy — Operator Privilege Privilege Level Example of Prompt and Permitted Operations Operator Level HP Switch> show setup View status and configuration information.