How do I set up my HP 2920 switch?

How do I set up my HP 2920 switch?

How to: Configure a HP ProCurve switch

1. Step 1: Connect your serial connection.
2. Step 2: Conenct PuTTY.
3. Step 3: Get the IP address.
4. Step 4: Set time server.
5. Step 5: Set SNMP community info.
6. Step 6: Launch the web GUI.
7. Step 7: Configure basic info.
8. Step 8: Create VLANs.

How do I configure my HP?

To do so, do one of the following:

1. Enter setup at the CLI Manager level prompt. HP Switch# setup.
2. Select Run Setup in the Main Menu of the menu interface.

How do I change my IP address in Aruba?

To configure the AOS switch IP address of the out-of-band management port:

1. Enable out-of-band management (oobm). AOS-switch(config)# oobm enable.
2. Assign an IP address to the oobm port. AOS-switch(config)# oobm ip address 10.2.100.68 255.255.255.0.
3. Add a default gateway to the oobm port.
4. Save the configuration.

How do I change the IP address on my HP ProCurve Switch?

HP Procurve Switch # [Tab] to the IP Config (DHCP/Bootp) field and use the Space bar to select the Manual option. [Tab] to the IP Address field and enter the IP address that is compatible with your network. [Tab] to the Subnet Mask field and enter the subnet mask used for your network.

How do I connect my HP switch?

To connect a console to the switch, use the console cable shipped with the switch and connect a PC or VT-100 terminal to the console serial port. The PC or terminal then functions as a management console connected directly to the switch.

How do I access HP switch from command line?

When moving between interfaces, the switch retains the current privilege level (Manager or Operator). That is, if end-user are at the Operator level in the menu and select the Command Line Interface (CLI) option from the Main Menu, the CLI prompt appears at the Operator level.

How do I find my HP configuration?

Click the My devices tab. The product name and model number display on the tile for your notebook. Click your product name on the My devices screen, and then click Specifications. Scroll to view video, audio and power specifications, and installed software.

What is the default IP address for Aruba switch?

In the factory default configuration, the switch has no IP (Internet Protocol) address and subnet mask, and no passwords.

What is the default IP of HP switch?

192.168.2.10
Switch factory-default settings

Parameter	Factory Default Setting
Password
IP address	192.168.2.10
Subnet mask	255.255.255.0
Default gateway	Not set

How do I check my HP switch settings?

To display the running configuration using the WebAgent:

1. In the navigation pane, click Troubleshooting.
2. Click Configuration Report.
3. Use the right-side scroll bar to scroll through the configuration listing.

What are the switches in the HP 2920 series?

The HP 2920 Switch Series consists of five switches: the 2920-24G and 2920-24G-PoE+ switches with 24 10/100/1000 ports and. the 2920-48G, 2920-48G-PoE+, and 2920-48G 740W PoE+ switches with 48 10/100/1000 ports.

Where is the serial port on HP ProCurve 2920?

HP-2920-48G-PoE Procurve Console Port with the serial console port. You need to find the RJ45 to 9-pin serial console cable in the box with your switch. Plug the RJ45 end into the console port which you will find on the left-hand side of the front of the switch and plug the 9-pin serial end into the serial port of your computer.

How to enable or disable stacking on hp 2920?

If stacking is disabled, enter the command stacking enable, which causes the switch to reboot. NOTE:By default, stacking is enabled on all HP 2920 switches when a Stacking Module is installed before the switch is powered up for the first time, but if the switches were powered up without a Stacking Module installed, stacking is disabled

Why is chain topology not supported in hp 2920?

A chain topology is not recommended because any hardware or software failure in the stack causes lost ports, which increases the amount of time for recovery of full stack operation due to multiple reboots. See the HP 2920 Installation and Getting Started Guidefor supported topologies. Boot the Standby and Member switches.