What kind of modem does Raspberry Pi 3 use?

I have the same setup (Raspberry Pi 3, operating system from 2017-11-29-raspbian-stretch-lite.img, USB mobile broadband modem Huawei E3372h-153). The modem shows up in lsusb a bit differently than yours though:

Is the Huawei e3372 USB modem in Hilink mode?

However, other sources suggest that the device in HiLink mode would rather be eth1. If you can access the web UI configuration interface at http://192.168.8.1/ when using the device under Windows, it also proves the device is in HiLink mode.

Why does my Raspberry Pi not work in stick mode?

For /dev/ttyUSB… to exist and wvdial etc. to work, the modem has to be in stick mode. The fact that no /dev/ttyUSB0 and /dev/ttySUB1 (modem interfaces) are created on your system seems to indicate your device is in HiLink mode. The presence of wwan0 in ifconfig output could be an indicator for that as well – it does not appear there on my setup.

Why is there no modem dialer in Raspbian?

Note: By default, ie with no modeswitch Linux only sees the storage device, which is why the OP cannot see or use the PPP Dialer or the Wireless Device. Once the modem is turned on using the modeswitch, wvdial, or one of it’s many replacements, controls access to the outside world.

Is there a firmware update for Huawei e3372s?

If any of you have experience with Debian/Rasbian/Linux incoming connection problems with Huawei E3372s or relative 3G/4G USB product which use CDC_ETH and have found solution to this problem You don’t need a firmware update, but you do need a modeswitch, which you’ve found, and a dialer, which you haven’t found.

How to tell if you have internet connection on Raspberry Pi?

Confirm you have an Internet connection: the wvdial output should show that a remote IP was assigned to the connection, and ifconfig should show you proper values for inet, netmask and destination for the ppp0 device. If so, a ping should work, for example on the omnipresent Google nameserver: ping 8.8.8.8.

What does disown do on Raspberry Pi 3?

The & disown allows you to close the terminal window / SSH connection while keeping the Internet connection up. Confirm you have an Internet connection: the wvdial output should show that a remote IP was assigned to the connection, and ifconfig should show you proper values for inet, netmask and destination for the ppp0 device.

How to tell if Huawei USB modem is in Hilink mode?

If you can access the web UI configuration interface at http://192.168.8.1/ when using the device under Windows, it also proves the device is in HiLink mode. This interface should also be accessible under Linux (worked for me with another Huawei HiLink modem), but only after your wwan0 is configured with a suitable IP address to access this subnet.

Can a Raspberry Pi 3 boot from USB?

The Raspberry Pi 3 B+ is able to boot from USB without any changes, but the Raspberry Pi 3 requires the USB boot bit to be set in the OTP (one-time programmmble). To enable the USB boot bit, the Raspberry Pi 3 needs to be booted from an SD card with a config option to enable USB boot mode. Once this bit has been set, the SD card is no longer

Why is my USB modem not working on my Raspberry Pi?

So this means ttyUSB2 is likely the modem if I have only one modem on the pi’s USB ports. wvdial worked after I edited two parts of it. One is to change the value of Modem to /dev/gsmodem I found above. The other is Init1 to Init4 lines. These strings are sent to the modem to initialize it when wvdial command is executed.

Is the AirCard 313U not recognized on Windows?

Solved: AirCard 313U (AT) not recognized on Windows – NETGEAR Communities × We are experiencing intermittent login issues for several of our services along with product registration. We are investigating this as the highest priority and will provide updates at Status.NETGEAR.com × We are experiencing login issues for several of our services.

How to get Windows 10 to recognize at & T AirCard?

Have another thing we can try to do is Click on your windows/start button go to File Explorer then on the left hand side Click This PC on this screen you should see Devices and Drives If you see a Drive named AT or tru-install Right click on it and then select eject once this ejects see if Windows 10 sees and installs the aircard.

Why is my at & T AirCard 340u not recognized?

Also note, it’s not that the device drivers don’t install, windows never notices that ANYTHING usb has been plugged in so it never even tries to look for drivers… It didn’t work on a Windows 8.1 machine either. The 340U powers up, but the device screen never shows the “ready to connect” screen. Only flashes the At&t logo.

What kind of modem does Raspberry Pi 3 use?