Are Quadrajet carburetors any good?

Are Quadrajet carburetors any good?

The truth is, a properly tuned Quadrajet can be just as efficient and reliable as a bolt-on substitute performance carburetor. The Quadrajet has many model designations; the most adaptable units were designated as 4M, 4MC and 4MV, and most were rated at 750cfm until 1972 when their rating was increased to 800cfm.

What causes a Quadrajet to flood?

99% of all quadrajet flood overs happen when its hot and its because of the float being saturated. HOWEVER that being said there is a reason that little clip was put in there. Properly installed that clip will not cause a problem.

Is a Quadrajet worth rebuilding?

A full and in-depth article of the rebuild process that Jet Performance takes with a Q-Jet Carburetor, by Dragzine.

How does a Rochester Quadrajet work?

The Quadrajet is a “spread bore” carburetor; the primary venturis are much smaller than the secondary venturis. Most Quadrajets use a vacuum operated piston to move the primary metering rods to control the air-fuel ratio, allowing the mixture to be lean under low load conditions and rich during high load conditions.

What carbs replace quadrajet?

New Holley Sniper EFI is Direct Replacement for Q-Jet Carb. Holley/MSD is thrilled to announce the release of Sniper EFI Systems for Quadrajet applications, which eliminate the need to continually rebuild 50-plus-year-old Quadrajet carburetors on classic Chevys, Pontiacs, Buicks, Oldsmobiles, and GMCs.

What is a divorced choke quadrajet?

PHOTO 3 A divorced choke uses a spring housing that is separate from the carburetor body. Some Rochester Quadrajet carburetors employed a divorced choke spring that is very sensitive to intake manifold heat to open the butterfly.

How do I identify my Rochester Quadrajet carburetor?

All Rochester Quadrajet carburetors are identified by a seven- or eight-digit GM part number. On units made before mid-1968, the part number was stamped around the outside edge of a round metal tag attached to the fuel bowl.

What CFM is my quadrajet?

Quadrajets can range anywhere in between 600 and 800 CFM. Most are rated 750 CFM or higher. Quadrajets are used by many GM street car enthusiasts; however, they are also disliked by just about as many.

How do I know if my quadrajet is 800 cfm?

When looking through the primaries, if you see a pronounced bulge protruding from the side of the wall surface, you have an 800 cfm carburetor. The primary wall of the 750 cfm unit does not have this bulge, and is consistent throughout. In the early ’80s, GM incorporated electronic connections to the Quadrajet.

What can replace a quadrajet?

Holley/MSD is thrilled to announce the release of Sniper EFI Systems for Quadrajet applications, which eliminate the need to continually rebuild 50-plus-year-old Quadrajet carburetors on classic Chevys, Pontiacs, Buicks, Oldsmobiles, and GMCs.

What are the common problems with Rochester Quadrajet?

A common problem is the fuel filter inside the fuel inlet housing becomes plugged with debris from dirty gasoline. This prevents the float bowl from filling quickly and results in poor engine performance. This filter is not an ideal candidate since it is made of paper and can not be seen unless the filter is removed from the housing.

How to troubleshoot a Quadrajet carburetor with mikes?

Look for any cracks around the area the seat screws in. Timing, dwell & idle adjustments. Look for any fuel restriction – check for kinks in the fuel line. Replace any fuel filters – There is usually one in the fuel inlet of the carburetor and often there will be an in-line fuel filter.

What happens when you close the choke on a Quadrajet?

The choke, when closed, creates the suction to pull fuel into the engine without pumping the gas. Pumping the gas a couple times can also start the engine, since the carburetor has an accelerator pump. However, it’s easy to flood the engine this way. Move the throttle by hand just a little and see if the choke snaps closed.

Why is the power valve sticking on my Quadrajet?

The power valve may be sticking. It needs to move up and down freely. Dirt in the system – take the top off the carburetor. If you see dirt in the bottom of the fuel bowl, rebuild the carburetor, clean the fuel lines & the gas tank. Main metering jet may be the wrong size.