How do I find network interfaces in Solaris 11?

Another easy way to quickly check the interface link status – is to check “ifconfig -a” command output. The RUNNING flag is cleared when the link is down. # ifconfig -a …… e1000g0: flags=1000843[UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 192.168.

What is Dladm in Solaris?

Only a single command interface, the dladm command, is needed to configure network driver properties. A uniform syntax is used regardless of the properties: dladm subcommand properties datalink .

How to add default route in Solaris 11?

Creating Persistent (Static) Routes

Use the route command with the –p option to persistently add a route: # route -p add default ip-address.
Display the currently active routes on a system by using the netstat command with the following options: # netstat -rn.

How do I find my NIC firmware Windows?

Expand Disk drives. Right-click on the drive and select Properties. Select the Details tab and select Hardware lds from the drop down menu. The firmware version will be displayed on the far right.

How do I know my IGB version?

Verify the Driver Version (Oracle Solaris 11)

Check the version of the installed driver. # strings /kernel/drv/arch/igb | grep igb igb 2.2.2. If the version number is not 2.2.
Manually load the module. # modload /kernel/drv/ arch /igb. where arch is amd64 for 64-bit Intel systems or sparcv9 for Oracle SPARC systems.

How do you check Ethernet is up or down?

How to check network adapter status in Linux

The above command indicates that my Ethernet is up and running with 192.168. 2.24/24 IP address.
Run: sudo ethtool -i eno1.
Run wavemon command to find out Wireless network speed, signal Strength and other information from the CLI: wavemon.

How do you delete IP address in Solaris 11?

How to Change and Configure Solaris 11 IP Address

To change the IPv4 static IP address, use below prefix: ipadm delete-addr /v4.
[Configure an interface with DHCP:
Manually Configuring the Default Route for a System: route -p add default

How do I plumb an IP address in Solaris 11?

Configuring the IP address

Step 1 : Set the NCP. We would set the NCP to DefaultFixed profile in order to configure the IP address manually.
Step 2 : Check the link status. The command “dladm show-dev” does not work in Solaris 11.
Step 3 : Create a new interface.
Step 4 : Creating IP address.

How do I create a persistent route in Solaris 11?

Creating Persistent (Static) Routes

Use the –p option to add a persistent route: $ route -p add default ip-address.
Use the –name option to add a persistent route by specifying a name rather than destination and gateway: $ route -p add destination-address gateway-address -name name.

How to check the firmware version in Solaris?

But not sure how to get the firmware version. Which firmware are you talking about? Thanks for contributing an answer to Unix & Linux Stack Exchange! Please be sure to answer the question. Provide details and share your research! But avoid … Asking for help, clarification, or responding to other answers.

Which is the latest version of Oracle Solaris OS?

This section describes the system firmware versions and Oracle Solaris OS versions to use with the current Oracle VM Server for SPARC software. You can run the Oracle VM Server for SPARC 3.3 software with at least the minimum versions of the system firmware and Oracle Solaris OS.

What does a ” patch ” mean in Oracle Solaris?

In the Oracle Solaris OS, a “patch” is a way of changing a small section of a release, without replacing the whole thing. A “patch” is also just a term for describing any update that is delivered through the My Oracle Support site.

What is the fcinfo command in Solaris 11?

The following examples show the most common administration operations that can be performed by using the fcinfo command: To list information of the HBA ports and their link statistics use the fcinfo hba-port -l command. To list all the remote ports on all the HBAs, use the fcinfo remote-port command.

How do I find network interfaces in Solaris 11?