How do you change the camera on an axis?

How do you change the camera on an axis?

Go to Configuration > Devices > Cameras. Select the camera to be replaced > Edit > Change the IP address to the new camera’s IP address > OK. This enables AXIS Camera Station to update the camera information and apply configurations from the old camera to the new camera.

How do I access my axis camera locally?

To access your site from a remote location open up AXIS Camera Companion 2.0 and log in with the same MyAxis account as used on the local site. Select the remote site, type in the site password and press Enter. You should now be connected to the site. your cameras and router up manually.

How do I change the IP address of my axis camera?

Power cycle the camera, i.e. turn the power off and turn it back on. Start AXIS IP Utility. When the camera appears in the window, right-click it and select “Assign new IP address” and enter the IP address. Click the “Assign” button and follow the instructions.

How do I log out of AXIS camera?

Select Actions to start or stop a recording manually, and change the status of I/O ports. See Record manuallyand Monitor I/O ports. Select Help to select the help related options. Select Log off to disconnect from the server and log off from the AXIS Camera Station client.

What port does Axis cameras use?

AXIS Camera Station server to device

Port	Number	Protocol
Main HTTP port	80	TCP
Main HTTPS port	443	TCP
Default bonjour port	5353	UDP
Default SSDP port	1900	UDP

What is the default password for AXIS Camera?

Axis: Traditionally root/pass, new Axis cameras require password creation during first login (note that root/pass may be used for ONVIF access, but logging into the camera requires root password creation) Basler: admin/admin.

What is the default IP address for Axis cameras?

192.168.0.90
The default IP address for the Axis cameras and video encoders is 192.168. 0.90. More information can be looked up here.

How do I discover my Axis camera?

Double click on the desktop icon that says Setup Axis Camera to launch the Setup Axis Camera Tool. The camera should be automatically detected and the green indicator light should be lit. If it is not, make sure the camera is powered on (the ring on the camera face should be green) and connected to your computer.

What operating system do Axis cameras use?

ARTPEC. ARTPEC (Axis Real Time Picture Encoder Chip) is an Application-specific integrated circuit developed by Axis Communications which powers many AXIS cameras. There are currently 7 generations of the chip. All chips run AXIS OS – a modified version of Linux meant for embedded devices.

How do I reset my axis camera?

Axis Factory Reset

1. Disconnect the camera from the power supply and ethernet.
2. Remove the four screws securing the rear cover and remove it.
3. Keep the Control button pressed while you restore the power supply.
4. Hold down the button for about 15 seconds until the status LED is yellow flashing.
5. Release the Control Button.

What is the default IP address for AXIS camera?

Can 2 IP cameras share the same port?

In your case, both are IP cameras. You will need to edit the settings of at least one of the cameras to use a port other than the default port 80. Each camera will be at its own LAN IP address; one using say port 80; the second using maybe port 8080.

How do I Configure my axis camera on my computer?

If you need to configure the camera manually, follow the instructions above for connecting the camera to the computer and setting the IP, then open a web browser and enter 192.168.0.90 in the address bar and press enter. You should see a Configure Root Password page, set this password to whatever you would like, but admin is recommended.

How does axis camera station service control work?

AXIS Camera Station Service Control automatically starts after the installation is complete. Double-click the AXIS Camera Station Client icon to start the AXIS Camera Station client. When starting the client for the first time, it automatically attempts to log in to the AXIS Camera Station server installed on the same computer as the client.

How to find the perfect Axis Communications camera?

Audio management software Audio system devices 2N SIP Mic Customer stories See our solutions at work with our customers Product selector Compare products to find your perfect match AXIS Site Designer

How to configure an axis camera using smartdashboard?

Click Setup to go to the setup page. On the left side click Users to open the users page. Click Add then enter the Username FRC Password FRC and click the Administrator bubble, then click OK. If using the SmartDashboard, check the Enable anonymous viewer login box.