How do you integrate Tasmota in home assistant?

How do you integrate Tasmota in home assistant?

Configuration

1. Browse to your Home Assistant instance.
2. In the sidebar click on Configuration.
3. From the configuration menu select: Integrations.
4. In the bottom right, click on the Add Integration button.
5. From the list, search and select “Tasmota”.
6. Follow the instruction on screen to complete the set up.

What is Tasmota home assistant?

Home Assistant Tasmota integration allows you to control Tasmotized Devices over MQTT without having to add a tone of YAML code.

How do I set up my Tasmota MQTT?

Configure MQTT using WebUI Go to Configuration -> Configure Other and make sure “MQTT Enable” box is checked. Once MQTT is enabled you need to set it up using Configuration -> Configure MQTT. While here, you might as well change the Friendly Name into something more descriptive than generic “Tasmota”.

Do I need MQTT with home assistant?

Most likely you will use it to communicate with your devices. But Home Assistant doesn’t care where the data is coming from or is limited to real hardware as long as there is MQTT support. This means that it doesn’t matter if the data is coming from a human, a web service, or a device.

Can’t connect to Tasmota?

If your device does not connect to your Wi-Fi and you’ve made sure the Wi-Fi credentials are correct, it is caused by using special chars or white spaces in your SSID or Password of your Wi-Fi. Remove them and try again. Other reason can be using an SSID longer than the allowed 32 characters.

How do I set up my Tasmota device?

After you have connected to the Tasmota Wi-Fi AP, open http://192.168.4.1 in a web browser on the smartphone (or whatever device you used). Depending on the phone, it will take you to the Tasmota configuration page automatically, or you will get a prompt to sign in to Wi-Fi network or authorize.

How do I use MQTT on Home Assistant?

MQTT

1. Browse to your Home Assistant instance.
2. In the sidebar click on Configuration.
3. From the configuration menu select: Integrations.
4. In the bottom right, click on the Add Integration button.
5. From the list, search and select “MQTT”.
6. Follow the instruction on screen to complete the set up.

Why should I use Tasmota?

Robust and speedy communication over MQTT Tasmota makes use of the lightweight communication protocol MQTT. This means that there is almost no delay when sending and receiving commands from Tasmota. For example when you switch the light on or change the colour, it is very quick to respond.

What is Tasmota used for?

Tasmota is custom firmware that is available for ESP8266 based devices allowing for web, timer, OTA firmware updates and sensor support. Tasmota allows for ESP8266 based devices to be controlled via HTTP, MQTT and KNX allowing for integration into just about any home automation ecosystem available.

How do you reset a Tasmota device?

Procedure

1. Cut power from the device completely for 30 seconds.
2. Power the device on and off six times with intervals lower than 10 seconds and leave it on after seventh time.
3. Fast power cycle device recovery should activate and the device should be reset to firmware defaults.

How to set up tasmota integration with home assistant?

At this point, I could reliably get the device discovered by Home Assistant by entering the Tasmota console and entering SetOption19 0 (the device shows up on the integration’s card at /config/integrations ). I did not need to toggle back and forth to SetOption19 1 like others have suggested, I just did SetOption19 0 a second time if needed.

How to use tasmota auto discovery in home assistant?

Enter the user name and password for your MQTT broker. If you are using MQTT in Home Assistant, it will be the same user name and password that you use to log in to Home Assistant. Enter your device name with no spaces under topic. This is the name that MQTT will use when communicating with the broker.

How to set shutter position on SONOFF tasmota?

Combination of configs found in issue #2839 and Home Assistant forum thread Sonoff IFan02 (Tasmota) MQTT Fan. Configure the device as Sonoff S31, and run: SetOption4 1, SetOption59 1. For shutter position to persist in Home Assistant through device reboots, execute PowerRetain 1.

How do you configure a new tasmota device?

Firstly click Configuration to access the main configuration menu. At this stage you should configure your Tasmota device. This process will tell the Tasmota firmware about your particular hardware and whether or not it should function as a plug, switch or some other device.