Contents
How many channels are there in the STM32 ADC?
The STM32F103C8 (Blue Pill) & STM32F432KC have a 12-bit ADC which is a successive approximation analog-to-digital converter. It has up to 18 multiplexed channels allowing it to measure signals from sixteen external and two internal sources. A/D conversion of the various channels can be performed in single, continuous, scan, or discontinuous mode.
How is the sampling time calculated in STM32?
STM32 ADC Sampling Time ADC samples the input voltage for a number of ADC_CLK cycles which can be modified using the SMP [2:0] bits in the ADC_SMPR1 and ADC_SMPR2 registers. Each channel can be sampled with different sample times. The Total ADC Conversion Time is calculated as follows:
How to initialize GPIO pin 0 in STM32F4?
Now the GPIO Pin needs to initialized. The line of commands to initialize the Pin 0 of GPIO Port C is: After initializing the GPIO Pin, you need to initialize the ADC Mode. The explanation of each commands can be found in stm32f4xx_adc library inside stm32f4xx_adc.c file.
Where are the calibration codes stored in STM32?
The calibration codes are stored in the ADC_DR as soon as the calibration phase ends. It is recommended to perform a calibration after each power-up.
How to use STM32 ADC in a dimmer?
STM32 ADC Read LAB (LED Dimmer With Analog Pot.) Set up An Analog Input Pin (Channel 7) In single Conversion Mode (The Pot. Pin) The Application will have 3 versions each does the same thing which is read the ADC result and move it to the timer CCR register which decides the PWM duty cycle percentage on the output LED pin.
When to use dual Fast interleaved ADC mode?
The dual fast interleaved ADC mode is intended for the conversion of one channel. ADC1 and ADC2 convert the selected channel alternately with a period of 7 ADC clock cycles. This means that the channel is converted every 7 clock cycles. Each ADC converts the channel every 14 ADC clock cycles. With a 14 MHz ADC clock, it is thus possible to reach
When does the ADC start in single conversion mode?
In Single Conversion mode, the ADC does one conversion. This mode is started either by setting the ADON bit in the ADC_CR2 register (for a regular channel only) or by an external trigger (for a regular or injected channel), while the CONT bit is 0. Once the conversion of the selected channel is complete: If a regular channel was converted:
Is the stm32f303 a mixed signal MCU?
The STM32F303 are mixed-signal MCUs with an ARM ® Cortex ®-M4 core (with FPU and DSP instructions) running at 72 MHz. These are the superset devices in the STM32F30x series. The devices are equipped with: Up to 7x fast- and ultra-fast comparators (25 ns)
How is the ADC converted to a DMA?
Once this bit has been set, the ADC scans all the channels selected in the ADC_SQRx registers (for regular channels) or in the ADC_JSQR register (for injected channels). A single conversion is performed for each channel of the group. After each end of conversion, the next channel in the group is converted automatically.
How to start a DMA transfer in STM32?
Note the Mode parameter. If you set it to DMA_NORMAL, you would need to start another DMA transfer by calling HAL_ADC_Start_DMA () each time a transfer is completed. And if you don’t do it fast enough, you will get an ADC overrun error and lose some ADC samples.
How is the reading width of ADC2 configured?
The reading width of ADC2 is configured every time you take the reading. Attenuation configuration is done per channel, see adc1_channel_t and adc2_channel_t, set as a parameter of above functions. Then it is possible to read ADC conversion result with adc1_get_raw () and adc2_get_raw ().
How many analog channels are there in ADC2?
Although we have 10 analog channels available in ADC2, all these channels are shared among other resources. For example, ADC2 is shared with WiFi drivers, therefore you can only use it after WiFi drivers are not started. You have to make your program smart enough to switch between two resources.
How to calculate the sampling rate for ADC?
The ADC Sampling Rate (Frequency) is calculated using this formula: SamplingRate = 1 / Tconv For The Previous example where Tconv = 1µs, The samplingRate = 1000000 = 1Ms/sec STM32 ADC Resolution, Reference, Formulas