How much torque do you need for struts?

Torque the strut to knuckle bolts to 63 ft/lb. Torque the top strut top nut to 41 ft/lb. check front wheel alignment, adjust camber etc as needed.

Does a 2008 Toyota Camry have shocks or struts?

Toyota Camry 2008, Front Strut Mount by Sachs®. The suspension strut mount is the upper mounting point of the shock absorber.

How do you install struts on a Toyota Camry?

Replace the Rear Struts in a Camry

Pop the hood and disconnect the negative battery cable with a wrench.
Disconnect any sensors or brackets from the strut and remove the stabilizer bar link nut midway down.
Pull the strut out and compress the spring.
Position the strut to the frame and install the upper mounting nuts.

Is a torque wrench necessary for struts?

Registered. You can replace your struts without a torque wrench but of course it’ll be better to have one. A lot of suspension components on cars aren’t supposed to be much tighter than you can do with your bare hands anyway (IE: no air tools).

Do you need a torque wrench for suspension?

Torque wrenches are essential to do things to spec but aren’t generally mandatory. It comes down to your level of detail. If you run aftermarket wheels or ever intend to a torque wrench is critical. definitely meant torque wrench, sorry for any confusion.

How much does it cost to replace struts on a Toyota Camry?

Toyota Camry Suspension Shock or Strut Assembly Replacement Cost Estimate. Labor costs are estimated between $224 and $283 while parts are priced at $311.

How long do struts last on a Toyota Camry?

Struts and shocks may need to be replaced anywhere between 50k and 100k miles. If at any time the struts or shocks are leaking, broken, or damaged, they should be replaced immediately.

How do I know when my struts are bad?

The Warning Signs Of Worn Shocks And Struts

Instability at highway speeds.
Vehicle “tips” to one side in turns.
The front end dives more than expected during hard braking.
Rear-end squat during acceleration.
Tires bouncing excessively.
Unusual tire wear.
Leaking fluid on the exterior of shocks or struts.

Can I replace shocks and struts myself?

Strut Replacement Replacing struts used to be a dangerous job for a DIYer. But these days you can buy a complete strut assembly that eliminates the strut/spring/mount disassembly process. These assemblies allow you to replace both of your front struts yourself in less than two hours.

How tight should car wheel nuts be with a torque wrench?

New wheels should be re-torqued after the first 50 to 100 driving miles.

Hardware Bolt or Stud Size	Typical Torque Range in Ft/Lbs	Minimum Number of Turns of Hardware Engagement
14 x 1.25 mm	85 – 90	9
7/16 in.	70 – 80	9
1/2 in.	75 – 85	8
9/16 in.	135 – 145	8

How much torque does a Toyota Camry have?

TOYOTA APPLICATION FT-LBS (N-m) AXLE SPINDLE NUT CAMRY (1994-92) 217 (294) CELICA (1992) & SUPRA 203 (276)

How big are the mounting nuts on a Camry?

Power Brake Booster Mounting Nuts: 10 ft. lbs. (120 inch-pounds) Camshaft Bearing Cap Bolts Journal No. 1 (intake and exhaust): 22 ft. lbs. Camshaft Sprocket Bolts: 40 ft. lbs.

How big is the water pump pulley on a Toyota Camry?

Timing Chain Tensioner Pivot Arm Bolt: 14 ft. lbs. Back-up Light Switch: 30 ft. lbs. Water Pump Pulley: 19 ft. lbs. Hub and Bearing Assembly-to-Axle Carrier Bolts: 59 ft. lbs.

What are the torque specifications of a Toyota?

TOYOTA CENTER BEARING LOCK BOLT 24 (33) CV JOINT BOLT 25 (34) INTERMEDIATE SHAFT MOUNT 40 (54) LOCKING HUB BODY-TO-AXLE BOLT 23 (31)

How much torque do you need for struts?