Contents
How to route all traffic from a specific port?
I have the following setup: A computer with two network cards connected to two different routers. The first router redirects all outside traffic coming on port 5122 to port 22. So that I can connect to the machine using ssh.
Is there an option to route specific traffic through a NIC?
Windows has no option to tell that outbound traffic to a specific port must go through a defined NIC. What about specific IP address? Yeah, ports don’t really come into it when you’re looking at routing, but you can definitely tell Windows to route traffic to a particular IP through a particular interface.
What does gateway mean in route specific traffic?
Gateway = The gateway needed to get to the destination, this can be your own IP if you’re on the same subnet. Cost = A number that helps Windows compare routes to the same address (lowest cost wins). Good luck.
What does default route mean in route print?
If you perform a route print from the command prompt then you’ll see a list of routes and their metrics. 0.0.0.0 denotes the Default Route, so if traffic is going through both NICs then I’d say you either: 1) Have a default gateway set on both NIC’s – this is bad, so remove the DFGW from the second.
Which is SonicWall route traffic through specific interface?
I have Sonicwall NSA 2400, it is configured with Percentage-Based WAN Load Balancing. My question is, given any LAN->WAN traffic originating from the X0 network, what steps would I need to take in the configuration to route all traffice from LAN->WAN for a given destination (example [74.125.45.100]) through a specific interface, in this case… X1
What’s the default bandwidth for a tunnel interface?
By default, older IOSes set the bandwidth of a Tunnel interface to 9 Kbps; on a 15.5 IOS I’ve just tested, the default bandwidth of a Tunnel interface is 100 Kbps. None of them reflects the bandwidth of the true physical egress interface the tunnel “went out”. As always, feel welcome to ask further!
Can a packet be forwarded through a tunnel interface?
Yes, it is. Essentially, forwarding a packet through a Tunnel interface means, literally, “prepend the tunnel headers to the existing packet, and perform a new routing lookup on the new resulting packet as if it was just received”.
Is it possible to not route HTTP traffic through a VPN?
Currently all traffic is routed through my vpn, i was wondering if it were possible to not route http and https traffic (80, 443) through the VPN. Here is the routing table when the system and openvpn client have started :
How to redirect to another port stack overflow?
In website list get inside a domain, click to Options tab, add these lines: ; Then go to website and wolaa 🙂 This is working HTTPS protocol too. Thanks for contributing an answer to Stack Overflow!
How to redirect a UDP port in iptables?
The syntax is as follows to redirect udp $srcPortNumber port to $dstPortNumber: iptables -t nat -A PREROUTING -i eth0 -p udp –dport $srcPortNumber -j REDIRECT –to-port $dstPortNumber. Replace eth0 with your actual interface name. The following syntax match for source and destination ips:
Which is the port for Apache redirect to?
In the following example, awesome.example.com and amazing.example.com would both be forwarded to some local service running on port 4567. I know this doesn’t exactly answer the question, but I’m putting it here because this is the top search result for Apache port forwarding.
How to specify a route to an interface?
Also, where you are specifying you want to add a route to a single IP 192.168.0.6, you need to use a subnet mask of 255.255.255.255. The subnet mask of 255.255.255.255 specifies a single host. A subnet mask of 255.255.255.0 specifies 192.168.0.X where X=1-254
Which is Unix and Linux stack exchange route traffic?
– Unix & Linux Stack Exchange route traffic on certain port through certain interface? I am currently running a system in which I need to be able to send and recieve HTTP and HTTPS traffic directly, however all other traffic must go via a VPN. x2 interfaces : eth0 (local network, behind a router) and tun0 (openvpn client)
How does a routing switch work on a routed port?
On a routed port, the switch does not perform Layer 2 switching logic on that frame. Instead, frames arriving in a routed port trigger the Layer 3 routing logic, including Making a Layer 3 forwarding decision by comparing the destination IP address to the IP routing table
How are requests routed through different network interfaces?
Requests are routed through the route with the lowest metric all else being equal The actual route chosen by Windows depends on several factors, including: the route metric, the specificity of the route (more specific routes, i.e. routes that match with a higher netmask are preferre), whether the route is a permanent or a dynamic route etc.
How to make a switch port act like a router port?
With that term, Cisco tells the switch to treat the port like it is a port on a switch—that is, a Layer 2 port on a switch. To make the port stop acting like a switch port and instead act like a router port, use the no switchport command on the interface. Once the port is acting as a routed port, think of it like a router interface.