When would you use a socket head cap screw?

When would you use a socket head cap screw?

Socket head cap screws are typically used in machine parts, die fixturing, and clamping. Socket head cap screws are ideal for applications in which there is not enough space to maneuver wrenches or sockets.

What is a cap head bolt?

Cap Screw. Refers to a hex head cap screw. This is a hex bolt with a circular washer face under the head. This does not extend past the edge of the hex as a flange bolt would. In most cases there is no operational difference between a hex head cap screw (left) and a hex bolt (right).

What’s the difference between a cap screw and a bolt?

The most basic difference between a cap screw and a bolt is the way in which these fasteners are installed. Technically, a bolt is installed by turning a nut to tighten the fastener, while a cap screw in installed by turning the head of the bolt to assemble and tighten.

What is a socket head cap screw?

Socket cap screws are commonly used in machine parts, die fixturing, and clamping. The socket head enables driving where there is not sufficient space for wrenches or sockets.

What are cap head screws used for?

Cap and machine screws are used to clamp machine parts together, either when one of the parts has a threaded hole or in conjunction with a nut. These screws stretch when tightened, and the tensile load created clamps the parts together.

What does a socket head cap screw look like?

A socket cap screws are machine screws with a cylindrical barrel shaped head containing a hexagonal socket. The head has a smaller diameter than most other machine screw heads, typically just 1.5 times the nominal thread diameter.

What is the head of a bolt called?

The cylindrical portion of the screw from the underside of the head to the tip is called the shank; it may be fully or partially threaded. The distance between each thread is called the pitch. Most screws and bolts are tightened by clockwise rotation, which is called a right-hand thread.

What are the different types of bolt heads?

Head Styles
Flat A countersunk head with a flat top. Abbreviated FH Oval A countersunk head with a rounded top. Abbreviated OH or OV
Round A domed head. Abbreviated RH Hex A hexagonal Head. Abbreviated HH or HX
Socket Cap A small cylindrical head using a socket drive. Button A low profile rounded head using a socket drive.

Do socket head cap screws need washers?

RE: Socket Head screws The primary reason to not use a lock washer on a SHC is that they don’t work. The compressive load required to completely flatten a helical washer and turn it into a “flat” washer is only a very small % of the targeted preload for a SHC.

What size is a tap bolt?

Typical sizes range from 1/4″ to 3/4″ in diameter while lengths span from about 3/4″ to 6″. Measure length from the underhead washer bearing surface to the threaded end of the bolt.

Why are caps and cups used with screws?

Plastic screw caps neatly snap into place to conceal flat head screws.

What material are socket head cap screws?

alloy steel
Socket Head Cap Screws are heavy duty screws made from DFARS sourced alloy steel. Manufactured in the USA by Parker Fasteners, these strong externally threaded screws offer the highest strength for commercial fasteners, and are the ideal fastener where there is not sufficient space for wrenches or sockets.

When to use Socket countersunk head cap screws?

Socket countersunk head cap screws from ITA Fasteners are mainly used in applications which require a visually pleasing fastener with minimal load bearing capabilities. So, please note that these screws are not intended to be used in high strength applications.

What’s the difference between a socket cap and a screw?

Head height is 50% of a standard socket head and the socket size is smaller. Similar thread design as a socket cap screw, but the dome-shaped head is wider and has a lower profile. Similar to a button head socket screw, but with an 82-degree countersunk flat head. Precision assembly work and applications requiring a well-tooled appearance.

How big should counterbore be for Socket Cap Screws?

The countersink or corner relief, however, should not be larger than is necessary to insure that the fillet on the screw is cleared. Normally, the diameter of countersink does not have to exceed F (max.).

Which is the best head for socket driven screws?

Button Head – Rounded head most often used in socket driven screws. Becoming more common with Torx / Six-lobe drives as well. Fillister Head – Smaller diameter and higher profile than round or pan heads allows for deeper slot. Flat Head (82 degrees) – Standard countersunk flat head screw. Allows for flat, smooth surface after installation.