Contents
How can I get 3V from a 5 volt circuit?
So back to our circuit, if we have 5 volts and want 3V from it, we use the formula above. If we use a 10KΩ as our R 1 resistor, plugging in the values, we get R 2 = (V) (R 1 )/ (V IN – V)= (3V) (10KΩ)/ (5V – 3V)= 15KΩ. So we can use a 15KΩ resistor as our R 2 resistor with the R 1 resistor being 10KΩ.
How does a low voltage DC converter work?
This low voltage circuit starts, the feedback voltage to bias to transistors inside the integrated circuit. This means that a short circuit, L1 is connected to pin 6 to ground, resulting in the accumulation of energy in the form of a magnetic field on current in L1 increases until a maximum value at about 1A.
Which is D3 for 3.3V 5V and 9V?
D3 is a 1N4007G, a glass-passivated model of the typical 1N4007, with regulated back EMF restoration. Its positioned, in conjunction with R2, to enhance EMI and the intended 3.3V, 5V, 9V outputs.
Is it possible to reduce DC voltage by resistors?
If these conditions are satisfied you can reduce DC voltage by (high power aluminium) resistors [>50 watt] Your battery is enough to supply at least 20x (or much more) current for your load. Power loss is not a problem.
Can you split 5V in half with resistors?
The 5V is now 2.5V. V CC is split in half. You may not always want half the voltage, but you can get the voltage to any level you want choosing the appropriate resistor values for a voltage divider circuit. Maybe your circuit is running off of 5V, yet you want only 3V to feed into a particular circuit element.
How big of a resistor should I use?
Typical sizes for small resistors are 1/8 Watt, 1/4 Watt, 1/2 Watt, 1 Watt, and so on. So in our case a 1/4 Watt (0.25) might be on the small size, but a 1/2 (0.5) Watt resistor should be fine. Using a larger Wattage resistor is almost always OK.
What kind of resistor do I need to run 12 volts led?
So to run a small LED off of 12 volts we need to use a 500 Ohm 1/2 Watt resistor. Enter any Starting Voltage, and then the Needed Voltage and finally the Current Draw (in AMPS) in the fields above then press CALCULATE to find other values.
How to calculate the voltage gain of an amplifier?
Going back to the earlier equation Av = 20 * Log (Vout/Vin) we can perform a bit of mathematical manipulation and say 10^ (Av/20)=Vout/Vin. So if our amplifier has a gain of 28dB, we find that our amplifier is boosting the input from the preamplifier by a factor of 10^ (28/20) or ~25.1.
How to convert 10 volts to 5 volts?
I’m going to need to convert a range of -10 to +10 volts into a range of 0 to +5 volts. How would this be accomplished? Thanks! Let me say something more. Inside of a torpedo there are gyroscopes. This gyroscope give -10 volts when the torpedo have 180 degrees of deviation to the west and 10 volts when the deviation is to the east.
How to convert voltage from one specifc range to another?
You could use a dual RRO op-amp (eg. AD8676) and ICL7660 as follows (single 5V supply) This has 0~5V output for -10~10V in. If you have to handle the -10V and +10V cases with an ADC that has a nominal 5V reference, then you may wish to increase R1 slightly to cover saturation voltage of the op-amps, resistor tolerances and so on, perhaps 5-10%.
Is it possible to convert 9V to 5V?
The current drain on the battery will only be (388 mW)/ (9 V) = 43 mA. Note that this is less than half of the battery drain resulting from using a linear regulator. Yes, it is possible using resistors.
Are there any 3V to 9V boost converters?
All Rights Reserved. Here are some 3V to 9V DC boost converter circuits that were requested by some of our visitors. It may be helpful to have one of this converters when no 9V battery is available or if you consider that they are too expensive.
Can you get 12V from a 3 volt DC converter?
You can get 12V too if you change the zener diode to a 12V version. Probably there are more 3 to 9 volt dc converters but for the moment those are the only ones presented in this article. No related posts.